Yuba City Garage Door Repair
A very common problem that people with garage doors face is that of excessive noise when it comes to opening and closing the doors. You should know that if your garage door starts making that annoying sound, it is usually because of loose hardware, worn rollers, or different parts of the garage door that might be in need of lubrication.
It can also be because your garage door opener needs anti vibration pads. These are not difficult to handle at all, and you can fix the issue yourself, provided you are well aware of the different parts your garage door consists of. However, if you think that you will not be able to achieve this yourself, you should seek help from the professionals at D&L Yuba City Garage Door Repair.
Basic Maintenance Requirements for Yuba City Garage Door Repair
These are some of the basic requirements that need to be taken care of when your garage door starts to make excessive noise. The noise is usually a result of a fault in one of the following factors described below:
Tighten Individual Parts
Make sure that all the bolts and nuts of your garage door are extremely tight because loose nuts are a major cause of excessive sound. You should also keep in check and replace any worn out parts that might exist. After you are done with this, be sure to add lubricant to all of the moving parts and components of your garage door. For doing this job, you can make use of a ratchet and a deep socket to tighten all the nuts. However, be sure that you do not make them too tight because that could cause problems later on as well.
Yuba City Garage Door Repair Can Replace Worn Out Rollers
If your rollers are worn out, you should replace them by loosening the bolts of the hinges and then taking the rollers off their tracks. Once you have replaced the rollers with new ones, you can put the hinges back into place. You should consider getting nylon rollers at the time of replacement because these nylon ones do not need as much oiling and are quieter as well. However, they are pricier than the steel rollers.
Install New Hinges By Yuba City Garage Door Repair
If your hinges need to be replaced, you should replace these with exactly the same hinges that your system is used to and requires. You can ensure this by matching the numbers of the hinges together and replacing them accordingly. You can even take your old hinges to the hardware store to be sure that you get exactly the same ones for your garage door. While there are fewer instances of the hinges becoming worn as compared to the rollers, they can still make a lot of sound if they become sloppy. A hinge will need to be replaced or cleaned when you see an oblong hole in it or signs of metal filings and gray dust.
Grease the Track
Start the process by wearing gloves and squeezing a large amount of grease onto your gloves. Wipe this grease all over the track. After the application process is complete, be sure to operate your opener a few times so that the grease will have a chance of spreading evenly all over the track along with the trolley.
Lube Every Moving Thing
Spray onto the hinges, roller shafts, and springs, and be sure to remove any excess amount of lubrication afterwards. After this, you can use a cardboard piece and put it behind the visible torsion springs, which you will also be spraying on. This lubrication should essentially be done after six months on a periodical basis so that you can make your door quiet and reduce the amount of wear considerably. Take care that you do not use lubricants such as grease, spray lithium grease, or oil for these parts because, while they may be cheaper, they do not work so well and gather a lot of grit and dust which you would not want.
Isolating The Opener
After you are done with the basic requirements, you should focus on isolating the garage door opener. This should especially be taken into consideration if your opener is making a lot of noise and is so loud that your family and neighbors get disturbed by it.
Adding Anti-Vibration Pads
You can make use of two anti-vibration pads. The first one can be placed in between the ceiling and the mounting bracket, while the second one can be placed underneath the bracket. After this, you can make use of an impact driver or a socket wrench to slip the new lag screw and fender washer together and place it within the rafter.
Fastening The Brackets To The Rafters
Next, place the rafters and the opener brackets together and use bolts to tighten all the four corners together.
When To Seek Professional Help Call Yuba City Garage Door Repair
While the repair and replacement of noisy overhead garage door parts might seem easy, it is a little technical, especially for those individuals who have never handled repair activities of garage doors before and have no idea what the individual parts look like.
Experts and professional at D&L Yuba City Garage Door Repair are here to help in exactly these kinds of situations. We provide our consumers and clients with in depth information on what their garage door requires after a careful inspection and then make sure that the repair services that we provide produce lasting and long-term results.
A noisy overhead garage door is never a good sign. It not only ends up irritating the peace and quiet of your home and neighborhood, it can also result in the damage of the moving parts of your garage door due to excessive dryness. It is therefore recommended that this problem be dealt with in an efficient manner as soon as it arises. After all, you would not want any long-term harm to come to your garage door! Call us at
Yuba City Garage Door Repair for all of your Yuba City garage door repair needs!
Follow Yuba City Garage Door Repair on Facebook for great savings.