Sacramento garage door opener repair

Garage Door Opener Repair

When it comes to garage door opener repairs, you should pay special attention to the replacement of worn out gears, especially if your garage door opener is chain driven. The shredded pieces of plastic gears are often a very common issue. However, the good news is that the repair of these worn out gears is not expensive and nor is it difficult.

Therefore, whenever your garage door opener sounds like it is working but does not open the door, you might want to get your gears checked instantly to see if there is any need for repairing. Here are some of the steps that you can follow in order to ensure that you effectively inspect and replace the gears of your door opener.

Preparation

Start by unplugging your garage door opener and then pulling onto the emergency release rope. Shut your garage door using your hand and remove the garage door opener cover. Make sure to focus on the chain drive carriage and the sprocket as well to see if there is any issue with these or not so that you can fix them immediately. A comprehensive overview is always a great way to handle the situation.

Inspect the Gears

You should thoroughly inspect your white plastic gears and see whether there is any evidence of worn out or shredded edges. If you do see a sign that they may be worn out, you should instantly replace them. However, before making an attempt to replace them, you should check out the model and the make of the garage door opener and look around for the appropriate gear that would fit in perfectly.

There are some great gear kits available online and at retail shops or with dealers. A complete gear kit will most likely consist of washers and two gears along with a grease tube. Some of them might also come with instructions regarding how you should carry out the process.

If, after your examination, you find out that your gears are in perfect shape, you might want to see if there is any other issue with your garage door opener. A professional company, like the D&L Garage Door might be able to help you in this regard. You can also choose to replace the entire unit yourself. However, carrying out the work yourself would require some level of expertise.

Collect The Tools

Replacement of the gear might require you to get access of the below stated tools:garage door opener

    • Hammer
    • Flat head screwdriver
    • 5/32-inch punch
    • 1/4-inch nut driver
    • 1/8-inch Allen wrench
    • 3/8-inch socket, driver, or nut
    • 5/16-inch socket, driver, or nut, along with extension

Loosen the Circuit Board

If you loosen your garage door circuit board, and allow it to dangle freely, you will realize that you will have much more room to carry out your work more effectively and efficiently. All you have to do is take the screws out and allow the circuit board to hang so that it can move out of your way.

Loosen the Chain

You will be able to spot a chain that is situated on the tensioning rod. Make use of a wrench so that you can pull the nut out of the rod. You might require another set of pliers or a wrench to make sure that the chain does not turn and remains in place.

Remove the Gear Assembly

Next, you will be required to remove those screws that help to hold your garage door’s gear assembly in one place. This will allow you to remove the whole of the assembly from the unit. After this, you will have to work on the helical gear and remove it from its shaft. A pin will be holding the gear in one place. This can be removed by a simple tap with the use of a hammer.

If you find that you are unable to remove the pin easily, you might want to spray a little WD-40 onto your pin and allow it to soak for a little while. This worn out gear which is hooked onto the motor shaft will then be easy to remove once you loosen the screws using a wrench. After this, take off the washers and the gear along with the screws that retain the gear onto the motor.

Reassemble the Gear Assembly

You will have to, then, attach the shaft with the new gear and reassemble and replace your motor assembly. After this, the helical gear assembly needs to be put in place. You can make use of the grease in your kit to make sure that the gears are attached perfectly and they would not fall out. Make sure that the chain is extremely tight and attached according to what the owner’s manual states. The garage door opener should then be covered, plugged in, and fully functional. You can finally enjoy a garage door opener that works perfectly.

When You Should Contact The Professionals

It is a great ideal to get in touch with a professional handyman or a company such as the D&L Garage Door who will be able to help you handle your garage door opener and its gear related issues, especially when you have no idea how to go about the situation. These experts are professionals in their field who happen to know more than a thing or two about fixing and repairing anything that deals with your garage doors. A company like D&L Garage Door is available throughout the week to their customers and is custom-centric in their approach.

Garage doors and garage door openers should not be taken lightly. They are an essential component of your homes, and neglecting them could pose a serious threat to the safety of your family and yourself. Therefore, be sure to fix any issue that comes up and never delay anything that needs to be repaired. You never know when some little issue would turn into something big.

garage door phone Sacramento California

Please Share: